AutoServiceTech.com Training today for tomorrow's challenges...

Add Even More Power To Your Lab Scope With These

A scope can only measure electrical signals, but that doesn't mean the tool is limited. With the addition of special adaptors, all types of information can be converted to signals you can view on the scope's screen. Here are a few items you may want to consider adding to your scope kit...and to your diagnostic arsenal!

PICO Protective Case

The only protective boot made for the PICO scope unit! It will help keep your scope unit clean and offers minor impact protection. It can be wiped down with nonabrasive hand cleaner and water. Show your Nerdz pride, and order one for your PICO today!

Our price: 30.00

PICO WPS500 Pressure Transducer

The WPS500 is an ultra high resolution pressure transducer. It features three pressure ranges (-15psi to 500psi, -15psi to 50psi, and -5psi to 5 psi), a zoom feature that removes ambient pressure from the pattern (kind of like using AC coupling with your low amp measurements), a rechargeable (via USB) Li-po battery, and pressure relief valve,all in a sturdy metal casing.

It can be used for nearly any pressure/vacuum test you want to perform and takes the place of owning several individual transducers. It can be used to measure fluid pressures (fuel pressure comes to mind!) as well. It has a response rate of 100 MICROSECONDS from 0 to 90% of full scale and a sensitivity of +/- 1% on the first two ranges, and +/- 5% on its lowest range.

Our kit is designed to let you unlock all the versatility this transducer has to offer, and includes:

WPS500 Transducer

User's manual

10mm, 14mm, and 18mm compression hoses

Ford Triton 16mm x 1.5mm compression hose

Exhaust adaptor

Vacuum adaptor

USB charging cable

BNC cable

Foster 2302 and 2202 coupler (if you want to make a connector of your own)

Be sure to compare kit contents before purchasing somewhere else!

Our price: 970.00

SenX "FirstLook" Sensor

Can't afford the WPS500 quite yet? Only interested in measuring exhaust pressure/vacuum signals? Than this may be the best choice for you! This sensor has a vacuum nipple on one end, and a BNC connector on the other. It measures pressure/vacuum and is an ideal tool for identifying engine breathing problems by measuring intake vacuum, exhaust pressure pulses, fuel rail pulses, and engine crankcase pressures. It is a very sensitive piezoelectric sensor, not suitable for running pressure checks, however.

Our price: 386.00

Coil On Plug Probe

Getting a secondary pattern on many coil-on-plug ignition systems can be a challenge. You can use the primary to see the burn line, but the firing line is not a match. You can buy special adaptors for each OEM coil you want to test OR you can use this probe. With it, if you can reach the coil you can get a pattern...

Our price: 173.00

PICO Mixmaster

Mixmaster can produce a parade display of up to 12 cylinders using a single channel of your lab scope. If you have a 2-channel scope, then Mixmaster can also display 2 engine banks separately with up to 6 cylinders per bank.

Mixmaster includes a trigger output, derived from one of the 12 input signals, which can be used to synchronise the scope to a known cylinder. Additionally, Mixmaster features a simple switch so you can invert a bank of signals to deal with negative-going signals on waste-spark systems.

Designed for use with the Automotive Oscilloscope Kit, Mixmaster can also be used on virtually any other lab scope, and can be used on both DIS and distributor ignition systems.

Mixmaster is battery powered and includes a low-battery indicator. The shockproof rubber case makes Mixmaster suitable for heavy-duty workshop use and incorporates a handy stand to make it easier to use.

Mixmaster is supplied with 3 BNC leads to connect to the oscilloscope, an engine-block ground lead, and a set of 4 short secondary ignition leads. Additional packs of secondary ignition leads can be purchased separately.

Mixmaster is a cost-effective way to display parade ignition waveforms on your lab scope. Compact and battery powered, it is ideal for mobile automotive diagnostics, and makes a valuable and inexpensive addition to your tool kit.

Our price: 325.00

PICO Break Out Leads

Piercing the insulation is the last choice for tapping into the electrical harness. Backprobing is often difficult to do on many connectors. The answer? These break out leads...

They come as as a set of three...small, medium and large spade (female/male) that allows you to tap in-line to most harness/sensor connectors. The separate pigtail allows you to plug in directly to the PICO scope leads.

Our price: 213.00